Single Drum 230/1/60 Motor

Morse Stationary Drum Roller

• Model: 1-5154VS-1-230
• 1/2 HP Motor: 230V 60 Hz Single Phase
• Liquid load capacity: 1,000 Lb. (455 kg)
• Dry load capacity varies:
  • 400 Lb. (182 kg) at 10 RPM
  • 300 Lb. (136 kg) at 20 RPM
    250 Lb. (114 kg) at 30 RPM
• Variable Speed: 1 to 38 RPM
• Designed to roll a steel drum 6” to 28” (15 to 71 cm) diameter and up to 40” 102 cm) long.
• Rotating drums to mix or blend material inside a closed drum saves time, labor and money.
• Drum rotating mixes drum contents to ensure homogeneity with less hazards.

Mixing contents inside your sealed drum eliminates the risks of spills and splashing of dangerous contents on workers during transfer, and greatly reduces clean-up, and the risk of contamination. It also eliminates use of special mixing vessels.

Variable Speed Drum Rollers are equipped with a Variable Frequency Drive (VFD) with motor starter and disconnect. Mount VFD on a wall and control drum rolling speed from 1 to 38 RPM.

Options Available:

• POLY-1-5154 (shown) for single drum roller
• POLY-2-5154 for double drum roller
• 1-5-1 Idler Attachment for 1 pail
• 1-5-2 Pair of Idler Attachments for use with Double Drum Roller

Enclosure Kits:

• GEK-1-5154-1 is Enclosure Kit with Safety Interlock for Single Stationary Drum Roller with 1-phase electric motor.
  GEK-2-5154-1 is Enclosure Kit with Safety Interlock for Double Stationary Drum Roller with 1-phase electric motor.

  GEK-1-5154-3 is Enclosure Kit with Safety Interlock for Single Stationary Drum Roller with 3-phase electric motor.
  GEK-2-5154-3 is Enclosure Kit with Safety Interlock for Double Stationary Drum Roller with 3-phase electric motor.

  GEK-1-5154-E1 is Enclosure Kit with Safety Interlock for Single Stationary Drum Roller with explosion-proof 1-phase electric motor.
  GEK-2-5154-E1 is Enclosure Kit with Safety Interlock for Double Stationary Drum Roller with explosion-proof 1-phase electric motor.

Install all Morse Rotators in accordance with local requirements for enclosure and safety interlock, etc. One way to accomplish this is with a Morse enclosure with safety interlock, so the rotator automatically turns off when enclosure door is opened. Power connections and motor controls must also comply with applicable local codes.

For OSHA compliance in the USA, see OSHA subpart O.1910.212(a)(4) "Barrels, containers, and drums. Revolving drums, barrels, and containers shall be guarded by an enclosure which is interlocked with the drive mechanism, so that the barrel, drum, or container cannot revolve unless the guard enclosure is in place."

• Save time, labor and money
• Blend ingredients right inside your sealed drum
• Eliminate transfer, clean-up, special vessels and apparatus
• Ensure Homogeneity
• Capacity:
  Liquid load: 1,000 Lb. (455 kg)
  Dry load varies:
  400 Lb. (182 kg) at 10 RPM
  300 Lb. (136 kg) at 20 RPM
  250 Lb. (114 kg) at 30 RPM

• Rotate one drum at any speed from 1 to 38 RPM.
• Find the best speed for each material.
• Some use high speed for initial mixing and low speed for prolonged agitation.
• Variable speed drum rollers are ideal for experimental use or where there is a variety of materials to be handled.
• ROTATE VARIOUS DRUM SIZES:
• Designed to roll a steel drum 6” to 28” (15 to 71 cm) diameter and up to 40” (102 cm) long.
• Add option # 1-5-1 to roll a smaller drum or pail. This simple bolt-on attachment enables you to relocate the idler wheel shaft assembly to adjust for various drum diameters.
• Set screws at each wheel permit easy repositioning to support various length drums.
• MOTOR SELECTION:
• The powerful 1/2 HP motor drives an efficient worm gear reducer connected to a solid 1” (2.54 cm) diameter shaft to turn four 6” (15.2 cm) diameter neoprene drive wheels.
• The four idler wheels turn freely on roller bearings.
• The basic motor is a three phase, 230/460V, 60Hz, TEFC motor.
• Other motor voltages, phases, enclosure types, etc. (for example: Explosion-Proof ***) or air motors are available.
• Motor controls are not included with the basic machines.
• Standard Stationary Drum Rotators are shipped without control, cord and plug and must be installed by an electrician according to local codes and customer’s preference.
• Explosion-Proof*** motors are rated for Class I Group D, and Class II Groups F and G.
• Air motors are vane-type and require correctly sized filter, regulator, lubricator, valve (FRL) and piping supplied by customer.
• Air Motor Technical Information Filter, regulator and lubricator (FRL) are available. • Part # 90010-P Description: KIT, 1/4” FRL & VALVE
• GROUNDING STRAP: Spring steel grounding straps are standard to help drain possible static charge from drum.
• DIMENSIONS: Base Dimensions: 24” x 55” (61 x 140 cm) Domestic Ship dimensions: L 63” W 40” H 20” (160 x 102 x 51 cm)
• Export ship dimensions: L 66” W 31” H 24” (168 x 79 x 61 cm)

Product Brochure - Click Here

Explosion Proof and custom units available

For more information please call 877-860-3620